There's no single best trailer brake. The right system depends on what you tow with, how heavy the trailer is, and whether it goes in the water. Here's how the four common systems compare: electric, surge, electric-over-hydraulic and air-over-hydraulic. We also cover where Bludot Manufacturing's hydraulic brake kits fit in.
Quick answer
- Electric drum brakes are the most common choice for utility, cargo and RV trailers that stay dry. They're simple and inexpensive, and they need a brake controller in the tow vehicle.
- Surge brakes are hydraulic brakes applied by the trailer's coupler. They need no controller and have long been a standard on boat trailers, but braking is less precise.
- Electric-over-hydraulic (EOH) uses your brake controller to run an electric pump that powers hydraulic disc or drum brakes. It's a strong choice for heavy trailers and boat trailers.
- Air-over-hydraulic (AOH) uses the tow vehicle's air brake system to power hydraulic brakes. It's built for heavy trailers pulled by trucks that already make air.
Side-by-side comparison
| Electric | Surge | Electric-over-hydraulic | Air-over-hydraulic | |
|---|---|---|---|---|
| How it's applied | A magnet in each drum, powered by the brake controller | The trailer pushes against the coupler, which pressurizes a master cylinder | The brake controller runs an electric pump that pressurizes the lines | Air pressure drives an actuator that pressurizes the lines |
| Brake controller needed | Yes | No | Yes (EOH-compatible) | No. Uses the truck's air brakes |
| Stopping power | Good, adjustable from the cab | Moderate. Depends on how hard the trailer pushes | Strong and consistent | Strongest of the hydraulic options |
| Water and salt | Poor. Magnets and wiring corrode when submerged | Good, especially with disc brakes | Very good with disc brakes and corrosion-resistant lines | Very good |
| Upkeep | Adjust shoes, check magnets and wiring | Check fluid, actuator and reverse lockout | Check fluid, pump and lines | Drain air tanks, check fluid and lines |
| Best for | Utility, cargo, RV and equipment trailers that stay dry | Boat trailers and rental trailers | Heavy boat, car-hauler and equipment trailers | Heavy trailers towed by trucks with air brakes |
Hydraulic vs. electric trailer brakes
Electric brakes use an electromagnet inside each drum. When you brake, the controller sends current to the magnets, which pull on an arm that pushes the shoes against the drum. Hydraulic brakes use pressurized brake fluid to push a wheel cylinder (drum brakes) or caliper piston (disc brakes), the same way the brakes on your truck work.
Electric brakes cost less and are easier to wire, and the controller lets you adjust braking from the cab. Hydraulic brakes, especially hydraulic discs, generally give more consistent stopping power on heavy loads, shed heat better on long downgrades, and hold up far better around water. A hydraulic system also needs something to create the pressure: a surge coupler, an electric-over-hydraulic actuator or an air-over-hydraulic actuator.
Choose electric if the trailer is light to mid-weight, stays out of the water, and you want the lowest cost. Choose hydraulic if the trailer is heavy, gets launched or sees road salt, or you want disc brakes.
Hydraulic (electric-over-hydraulic) vs. surge brakes
Surge and electric-over-hydraulic systems both use hydraulic wheel brakes. The difference is what creates the pressure.
- Surge pros: self-contained, no controller needed, works with any tow vehicle, and common on boat trailers.
- Surge cons: the trailer has to push against the tow vehicle before the brakes apply, so braking lags and can't be adjusted from the cab. Backing up needs a lockout, usually an electric solenoid or a manual pin, and some states restrict surge brakes on heavier trailers.
- EOH pros: the brakes apply as soon as you press the pedal, braking is adjustable through the controller, and it handles heavy loads and disc brakes well.
- EOH cons: costs more than surge, and needs a compatible brake controller and a solid 12-volt supply.
What about heavy-duty trailers?
For heavy equipment trailers, car haulers and goosenecks, the choice usually comes down to the tow vehicle. If the truck has air brakes, an air-over-hydraulic system gives the strongest, most consistent actuation while keeping simple hydraulic wheel brakes. If the truck doesn't make air, electric-over-hydraulic with disc brakes is the usual step up from electric drums. Either way, brakes on every axle and correctly sized lines matter as much as the actuator.
Which needs the least maintenance?
Hydraulic disc brakes with corrosion-resistant lines are usually the lowest-maintenance setup, especially on trailers that see water or salt. Discs are open, shed water and debris, and have no shoes to adjust. Electric drums need periodic shoe adjustment and magnet checks. On any hydraulic system, check the fluid, inspect hoses for cracks, and replace corroded lines before they leak. Our copper-nickel vs. steel brake line guide covers line choices.
Where Bludot Manufacturing fits
Bludot Manufacturing builds the parts that connect a trailer's brakes into a working system: hydraulic brake line kits, hoses, fittings, air-over-hydraulic kits and boosters. They're made in Muskegon, Michigan to the same specifications trailer manufacturers have relied on for over 50 years.
- Hydraulic brake line kits for single, tandem and torsion axles, from under $70 to about $290.
- Air-over-hydraulic brake kits for single, tandem and triple axles, with or without ABS.
- Replacement hoses, tubing and fittings for hydraulic trailer brake systems.
Not sure which kit fits? Contact our team with your axle count, axle type and brake type. For more on choosing a kit, read Trailer Brakes and Towing Safety.
Frequently asked questions
Are hydraulic trailer brakes better than electric brakes?
For heavy trailers and trailers that go in the water, usually yes. Hydraulic brakes, especially discs, give more consistent stopping and resist corrosion better. Electric brakes cost less and are a good fit for lighter trailers that stay dry.
Do hydraulic trailer brakes need a brake controller?
It depends on the actuator. Surge brakes don't. Electric-over-hydraulic systems need a compatible brake controller. Air-over-hydraulic systems run off the tow vehicle's air brakes.
What brakes are best for a boat trailer?
Hydraulic brakes, either surge or electric-over-hydraulic, usually with discs. Electric drum brakes don't hold up well to repeated submersion. Use corrosion-resistant brake lines and rinse the brakes with fresh water after launching in salt water.
What's the difference between surge and electric-over-hydraulic brakes?
Both use hydraulic wheel brakes. Surge brakes are applied when the trailer pushes against the coupler, so they need no controller. Electric-over-hydraulic brakes are applied by an electric pump that your brake controller runs, so they respond immediately and can be adjusted from the cab.
What brakes should I use on a heavy-duty trailer?
If your truck has air brakes, air-over-hydraulic is the strongest hydraulic option. Otherwise, electric-over-hydraulic with disc brakes on every axle is the common choice for heavy trailers.